filename: TFS1643A.doc version 4.0 09.12.2011 vectron international filter specification tfs 1643 a 1/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: input: 50 output: 50 characteristics remark: the maximum attenuation in the passband is defined as the insertion loss a e . the nominal frequency f n is fixed at 1643,5 mhz without any tolerance or li mit. the values of absolute attenuation a abs are guaranteed within the specified temperature ra nges. the frequency shift of the filter in the oper ating temperature range is included in the production tolerance schem e. d a t a typ. value tolerance / limit insertion loss (otr2) a e 2,2 db max. 3,0 db nominal frequency f n 1643,5 mhz passband pb (f n ? 15,5) mhz ? (f n + 13,0) mhz passband variation (otr2) 0,7 db 1,5 db absolute attenuation a abs 1525 mhz ? 1559 mhz (otr) 43 db min. 35 db @ 1670 mhz (otr2) ** 4 db min. 3 db @ 1675 mhz (otr2) min. 4 db 1884 mhz ? 1952 mhz (otr) 63 db min. 55 db return loss within pb (otr2) 9 db min. 8 db operating temperature range otr - - 40 c ... + 85c operating temperature range 2 otr2 - - 20 c ... + 85c storage temperature range - - 40 c ... + 85c temperature coefficient of frequency tc f * -42 ppm/k *) ? f c (hz) = tc f (ppm/k) x (t - t o ) x f cat (mhz) **) guaranteed values have to be understood as slo ping lines between the given attenuation value and the attenuation value of the following point or segment generated: checked / approved:
filename: TFS1643A.doc version 4.0 09.12.2011 vectron international filter specification tfs 1643 a 2/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. filter characteristic 1605 1615 1625 1635 1645 1655 1665 1675 -10 -8 -6 -4 -2 0 frequency in mhz magnitude in db 1000 1200 1400 1600 1800 2000 2200 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 frequency in mhz magnitude in db construction and pin connection (all dimensions in mm) 1 2 3 4 5 6 1,2 max. 0,6 0,75 3 ,0 +/-0,15 0,6 0,30x0,30 1 3 6 4 date code 50 ohm test circuit l1 saw l2 2 5 1, 3, 4, 6 h43a b50 1 ground 2 input 3 ground 4 ground 5 output 6 ground date code: year + week b 2011 c 2012 d 2013 ...
filename: TFS1643A.doc version 4.0 09.12.2011 vectron international filter specification tfs 1643 a 3/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plan, 3 pl ans; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 1 0 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao pull off direction pin marker typ date code ko t a c n w 1 w 2 the minimum bending radius is 45 mm. tape (all dimensions in mm) w : 8,00 0,3 po : 4,00 0,1 do : 1,50 +0,1/-0 e : 1,75 0,1 f : 3,50 0,05 g(min) : 0,75 p2 : 2,00 0,05 p1 : 4,00 0,1 d1(min) : 1,50 ao : 3,25 0,1 bo : 3,25 0,1 ct : 5,3 0,1 reel (all dimensions in mm) a : 180 w1 : 8,4 +1,5/-0 w2(max) : 14,4 n(min) : 60 c : 13,0 0,2
filename: TFS1643A.doc version 4.0 09.12.2011 vectron international filter specification tfs 1643 a 4/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260 c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: TFS1643A.doc version 4.0 09.12.2011 vectron international filter specification tfs 1643 a 5/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 - generation of development specification s.springfeldt 05.05.2011 2.0 - frequency limits of passband changed a. molke 01.07.2011 - limits for absolute attenuation updated (1670 ? 1675 mhz) 3.0 - second operating temperature range introduced a. molke 12.07.2011 3.1 - change from development spec to filter spec a . molke 03.08.2011 - typical values added - filter characteristic added 4.0 - limits for absolute attenuation updated (1670 ? 1675 mhz) a. molke 09.12.2011 - typical values updated
|
